#$&*
Phy 201
Your 'cq_1_00.1' report has been received. Scroll down through the document to see any comments I might have inserted, and my final comment at the end.
** **
The problem:
You don't have to actually do so, but it should be clear that if you wished to do so, you could take several observations of positions and clock times. The main point here is to think about how you would use that information if you did go to the trouble of collecting it. However, most students do not answer these questions in terms of position and clock time information. Some students do not pause the video as instructed. To be sure you are thinking in terms of positions and clock times, please take a minute to do the following, which should not take you more than a couple of minutes:
Pick one of the videos, and write down the position and clock time of one of the objects, as best you can determine them, in each of three different frames. The three frames should all depict the same 'roll' down the ramp, i.e. the same video clip, at three different clock times. They should not include information from two or more different video clips.
For each of the three readings, simply write down the clock time as it appears on the computer screen, and the position of the object along the meter stick. You can choose either object (i.e., either the pendulum or the roll of tape), but use the same object for all three measurements. Do not go to a lot of trouble to estimate the position with great accuracy. Just make the best estimates you can in a couple of minutes.
Which object did you choose and what were the three positions and the three clock times?
answer/question/discussion: ->->->->->->->->->->->-> (start in the next line):
I chose the pendulum. The three times were 29.234, 29.562, 29.671. The three positions were 7, 16, and 18.
#$&*
In the following you don't have to actually do calculations with your actual data. Simply explain how you would use data of this nature if you had a series of several position vs. clock time observations:
If you did use observations of positions and clock times from this video, how accurately do you think you could determine the positions, and how accurately do you think you would know the clock times? Give a reasonable numerical answer to this question (e.g., positions within 1 meter, within 2 centimeters, within 3 inches, etc; clock times within 3 seconds, or within .002 seconds, or within .4 seconds, etc.). You should include an explanations of the basis for your estimate: Why did you make the estimate you did?
answer/question/discussion: ->->->->->->->->->->->-> (start in the next line):
The positions would be within .3 inches. The clock times would be hard to estimate though. It would be more like .5 seconds to determine. I put these estimates because after watching the videos I could see easily see the places on the measuring tape and the clock.
@&
You report clock times that differ by about .3 second and .1 second. The first and last of the three clock times differ by less than .5 second. So the uncertainty is clearly less than +- .5 second. You'll need to give this part of the question as little more thought.
The +-.3 inches is a very reasonable estimate.
*@
#$&*
How can you use observations of position and clock time to determine whether the tape rolling along an incline is speeding up or slowing down?
answer/question/discussion: ->->->->->->->->->->->-> (start in the next line):
#$&*
How can you use observations of position and clock time to determine whether the swinging pendulum is speeding up or slowing down?
answer/question/discussion: ->->->->->->->->->->->-> (start in the next line):
You could watch time in between inches and look on the clock. Then you can see from inch to inch and determine the time per inch it takes on each one.
@&
Right idea. What then would be the specific criterion used to determine whether the pendulum is speeding up or slowing down?
*@
#$&*
Challenge (University Physics students should attempt answer Challenge questions; Principles of Physics and General College Physics may do so but it is optional for these students): It is obvious that a pendulum swinging back and forth speeds up at times, and slows down at times. How could you determine, by measuring positions and clock times, at what location a swinging pendulum starts slowing down?
answer/question/discussion: ->->->->->->->->->->->-> (start in the next line):
#$&*
Challenge (University Physics students should attempt answer Challenge questions; Principles of Physics and General College Physics may do so but it is optional for these students): How could you use your observations to determine whether the rate at which the tape is speeding up is constant, increasing or decreasing?
answer/question/discussion: ->->->->->->->->->->->-> (start in the next line):
#$&*
** **
10 minutes
** **
@&
As you'll see from my notes, the Phy 201 course is more rigorous than the 121 course and requires more thorough and detailed answers.
I don't think you'll have much trouble expanding and clarifying your answers. I'll be espectially interested to see how you answer the question of the time uncertainty.
&#Please see my notes and, unless my notes indicate that revision is optional, submit a copy of this document with revisions and/or questions, and mark your insertions with &&&& (please mark each insertion at the beginning and at the end).
Be sure to include the entire document, including my notes.
If my notes indicate that revision is optional, use your own judgement as to whether a revision will benefit you. &#
*@