#$&* course phy 201 2/10 10:30 005. `query 5
.............................................
Given Solution: `a**You would use accel. and `dt to find `dv: a * `dt = `dv. Adding `dv to initial vel. v0 you get final vel. Then average initial vel. and final vel. to get ave. vel.: (v0 + vf) / 2 = ave. vel. You would then multiply ave. vel. and `dt together to get the displacement For example if a = 3 m/s^2, `dt = 5 s and v0 = 3 m/s: 3 m/s^2 * 5 s = 15 m/s = `dv 15 m/s + 3 m/s = 18 m/s = fin. vel. (18 m/s + 3 m/s) / 2 = 10.5 m/s = vAve 10.5 m/s * 5 s = 52.5 m = displacement In more abbreviated form: a * `dt = `dv v0 + `dv = vf (vf + v0) /2 = vAve vAve * `dt = `ds so `ds = (vf + v0) / 2 * `dt. ** STUDENT QUESTION If we have the formula vf= v0 + a * dt, then we would substract the v0 from both sides to isolate the a * dt algebraically, so our formula would be vf-v0= a* `dt, how is this in comparison to the initial velocity v0 + the change in velocity(dv) = to the final velocity(vf). If we multiply the acceleration(a) times time(dt) we find the change in velocity(dv).......we then add the initial to the change to find the final....... Why do we add the initial to the change in velocity to find the final? INSTRUCTOR RESPONSE The initial velocity is v0, the final velocity is vf, so the change in velocity is `dv = vf - v0. Thus your early result vf-v0= a* `dt shows that a * `dt is equal to `dv. In general the change in any quantity is equal to its final value minus its initial value. It follows immediately from this that if you add the change in the quantity to its original value, you get its final value. The following two statements say the same thing: statement 1: If the temperature starts at 20 degrees and ends up at 35 degrees then it changed by +15 degrees. statement 2: If the temperature starts at 20 degrees and changes by +15 degrees then it ends up at 35 degrees. We generalize this to the two symbolic statements If a quantity Q changes from Q0 to Qf then the change is `dQ = Qf - Q0. If a quantity Q starts out at Q0 and changes by `dQ, then it ends up at Qf. These statements can be expressed as two equations `dQ = Qf - Q0 and Qf = Q0 + `dQ These two equations are algebraically equivalent: you can get the second by adding Q0 to both sides of the first, or you can get the first by subtracting Q0 from both sides and reversing sides. A third equation also follows: Q0 = Qf - `dQ, which can be interpreted in terms of the preceding examples into obvious statements. &&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&& Self-critique (if necessary):ok ------------------------------------------------ Self-critique Rating:ok ********************************************* Question: `qWhat is the displacement `ds associated with uniform acceleration from velocity v0 to velocity vf in time interval `dt? YYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYY Your solution: ds= Vave * dt confidence rating #$&*: 3 ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
.............................................
Given Solution: Since accel is uniform vAve = (v0 + vf) / 2. Thus displacement is `ds = vAve * `dt = (v0 + vf) / 2 * `dt, which is the first equation of uniformly accelerated motion. ** STUDENT QUESTION I failed to make reference to uniformly accelerated motion. What exactly is the difference between uniformly accelerated motion and average acceleration??? Will we be asked to differentiate between the two for problems, or is this something we should be able to determine on our own easily??? INSTRUCTOR RESPONSE Uniformly accelerated motion is motion in which the acceleration is uniform, unchanging. If motion is uniformly accelerated, then the acceleration is constant, so the acceleration at any instant is equal to the average acceleration. If motion is uniformly accelerated, then since the slope of the velocity vs. clock time graph represents acceleration, the slope is constant; i.e., the graph is a straight line. &&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&& Self-critique (if necessary):ok ------------------------------------------------ Self-critique Rating:ok ********************************************* Question: Describe the flow diagram we obtain for the situation in which we know v0, vf and `dt. YYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYYY Your solution: confidence rating #$&*: ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
.............................................
Given Solution: `a** The first level in the diagram would contain `dt, v0 and vf. From v0 and vf we can easily reason out `dv, so v0 and vf would connect to `dv in the second level. The second level would also contain vAve, also obtained from v0 and vf and therefore connected from vf in the first level to v0 in the first level. The third level would contain an a, which is reasoned out from `dv and `dt and so is connected to `dv in the second level and `dt in the first level. The third level would also contain `ds, which follows from vAve and `dt and is therefore connected to vAve in the second level and `dt in the first level. ** STUDENT QUESTION: I'm not sure what is meant by a flow diagram. I know that we can determine 'ds from the equation 'ds=(v0+vf)/2* 'dt. Then I can use 'ds to find other possible information by plugging this and other information into other equations. INSTRUCTOR RESPONSE The instructor's response developed into an entire document, a bit too long to include in this query without interrupting the flow. The document has been posted at http://vhcc2.vhcc.edu/dsmith/genInfo/qa_query_etc/ph1/flow_diagrams.htm and should be very useful to anyone who is having trouble with the idea of flow diagrams. STUDENT COMMENT Flow diagrams are useful in that they give us something to logically grind out. It's not enough to know that there are formulas to find variables. True learning is when a person can take whats given, twist it and manipulate it, and find other answers. &&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&& Self-critique (if necessary):
.............................................
Given Solution: `a** The flow diagram shows us the flow of information, what we get from what, usually by combining two quantities at a time. How we get each quantity may also be included. From vf and v0 we get `dv, shown by lines from vf and v0 at the top level to `dv. From vf and v0 we also get and vAve, shown by similar lines running from v0 and vf to vAve. Then from vAve and `dt we get `ds, with the accompanying lines indicating from vAve and `dt to `ds, while from `dv and `dt we get acceleration, indicated similarly. ** &&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&&& Self-critique (if necessary): ------------------------------------------------ Self-critique Rating: