Phy 122
Your 'flow experiment' report has been received. Scroll down through the document to see any comments I might have inserted, and my final comment at the end.
** #$&* Your initial message (if any): **
Haven't been able to find the describing graphs exercise yet.
Have some confusion over when to use the submit work form and when to copy and paste questions into query program, and then paste the send file into the submit work form.
Are all Problem Sets to be submitted via the send file method and book problems to be submitted through submit work form?
** #$&* Is flow rate increasing, decreasing, etc.? **
The picture below shows a graduated cylinder containing water, with dark coloring (actually a soft drink). Water is flowing out of the cylinder through a short thin tube in the side of the cylinder. The dark stream is not obvious but it can be seen against the brick background.
You will use a similar graduated cylinder, which is included in your lab kit, in this experiment. If you do not yet have the kit, then you may substitute a soft-drink bottle. Click here for instructions for using the soft-drink bottle.
In this experiment we will observe how the depth of water changes with clock time.
In the three pictures below the stream is shown at approximately equal time intervals. The stream is most easily found by looking for a series of droplets, with the sidewalk as background.
Based on your knowledge of physics, answer the following, and do your best to justify your answers with physical reasoning and insight:
As water flows from the cylinder, would you expect the rate of flow to increase, decrease or remain the same as water flows from the cylinder?
Decrease as there is less pressure forcing the liquid through the hole.
#$&*
As water flows out of the cylinder, an imaginary buoy floating on the water surface in the cylinder would descend.
Would you expect the velocity of the water surface and hence of the buoy to increase, decrease or remain the same?
Decrease as there is less pressure forcing liquid through the hole
#$&*
How would the velocity of the water surface, the velocity of the exiting water, the diameter of the cylinder and the diameter of the hole be interrelated? More specifically how could you determine the velocity of the water surface from the values of the other quantities?
The faster the water is exiting, the faster the velocity of the waters surface.
The larger the hole, the faster the velocity of the exiting water, and hence the water surface.
The larger the diameter of the cylinder (other things being equal) the faster the velocity of the exiting water. If the cylinder is wider then there will be more water pressing down.
#$&*
The water exiting the hole has been accelerated, since its exit velocity is clearly different than the velocity it had in the cylinder.
Explain how we know that a change in velocity implies the action of a force?
#$&*
What do you think is the nature of the force that accelerates the water from inside the cylinder to the outside of the outflow hole?
Gravity
#$&*
From the pictures, answer the following and justify your answers, or explain in detail how you might answer the questions if the pictures were clearer:
Does the depth seem to be changing at a regular rate, at a faster and faster rate, or at a slower and slower rate?
Slower and slower
#$&*
What do you think a graph of depth vs. time would look like?
negative expopnential slope
#$&*
Does the horizontal distance (the distance to the right, ignoring the up and down distance) traveled by the stream increase or decrease as time goes on?
Decrease, as the water's velocity is less and less.
#$&*
Does this distance change at an increasing, decreasing or steady rate?
decreasing
#$&*
What do you think a graph of this horizontal distance vs. time would look like? Describe in the language of the Describing Graphs exercise.
negative expopnential slope
#$&*
You can easily perform this experiment in a few minutes using the graduated cylinder that came with your kit. If you don't yet have the lab materials, see the end of this document for instructions an alternative setup using a soft-drink bottle instead of the graduated cylinder.
Setup of the experiment is easy. You will need to set it up near your computer, so you can use a timing program that runs on the computer. The cylinder will be set on the edge of a desk or tabletop, and you will need a container (e.g., a bucket or trash can) to catch the water that flows out of the cylinder. You might also want to use a couple of towels to prevent damage to furniture, because the cylinder will leak a little bit around the holes into which the tubes are inserted.
Your kit included pieces of 1/4-inch and 1/8-inch tubing. The 1/8-inch tubing fits inside the 1/4-inch tubing, which in turn fits inside the two holes drilled into the sides of the graduated cylinder.
Fit a short piece of 1/8-inch tubing inside a short piece of 1/4-inch tubing, and insert this combination into the lower of the two holes in the cylinder. If the only pieces of 1/4-inch tubing you have available are sealed, you can cut off a short section of the unsealed part and use it; however don't cut off more than about half of the unsealed part--be sure the sealed piece that remains has enough unsealed length left to insert and securely 'cap off' a piece of 1/4-inch tubing.
Your kit also includes two pieces of 1/8-inch tubing inside pieces of 1/4-inch tubing, with one end of the 1/8-inch tubing sealed. Place one of these pieces inside the upper hole in the side of the cylinder, to seal it.
While holding a finger against the lower tube to prevent water from flowing out, fill the cylinder to the top mark (this will be the 250 milliliter mark).
Remove your thumb from the tube at the same instant you click the mouse to trigger the TIMER program.
The cylinder is marked at small intervals of 2 milliliters, and also at larger intervals of 20 milliliters. Each time the water surface in the cylinder passes one of the 'large-interval' marks, click the TIMER.
When the water surface reaches the level of the outflow hole, water will start dripping rather than flowing continuously through the tube. The first time the water drips, click the TIMER. This will be your final clock time.
We will use 'clock time' to refer to the time since the first click, when you released your thumb from the tube and allowed the water to begin flowing.
The clock time at which you removed your thumb will therefore be t = 0.
Run the experiment, and copy and paste the contents of the TIMER program below:
Text1
1 0 0
2 1.058594 1.058594
3 2.3125 1.253906
4 3.558594 1.246094
5 4.839844 1.28125
6 6.28125 1.441406
7 8.140625 1.859375
8 10.46094 2.320313
9 13.41406 2.953125
10 18.65625 5.242188
#$&*
Measure the large marks on the side of the cylinder, relative to the height of the outflow tube. Put the vertical distance from the center of the outflow tube to each large mark in the box below, from smallest to largest distance. Put one distance on each line.
0
15.5
13.9
12.3
10.5
8.8
7.1
5.3
3.4
1.6
#$&*
Now make a table of the position of the water surface vs. clock time. The water surface positions will be the positions of the large marks on the cylinder relative to the outflow position (i.e., the distances you measured in the preceding question) and the clock times will as specified above (the clock time at the first position will be 0). Enter 1 line for each event, and put clock time first, position second, with a comma between.
For example, if the first mark is 25.4 cm above the outflow position and the second is 22.1 cm above that position, and water reached the second mark 2.45 seconds after release, then the first two lines of your data table will be
0, 25.4
2.45, 22.1
If it took another 3.05 seconds to reach the third mark at 19.0 cm then the third line of your data table would be
5.50, 19.0
Note that it would NOT be 3.05, 19.0. 3.05 seconds is a time interval, not a clock time. Again, be sure that you understand that clock times represent the times that would show on a running clock.
The second column of your TIMER output gives clock times (though that clock probably doesn't read zero on your first click), the third column gives time intervals. The clock times requested here are those for a clock which starts at 0 at the instant the water begins to flow; this requires an easy and obvious modification of your TIMER's clock times.
For example if your TIMER reported clock times of 223, 225.45, 228.50 these would be converted to 0, 2.45 and 5.50 (just subtract the initial 223 from each), and these would be the times on a clock which reads 0 at the instant of the first event.
Do not make the common error of reporting the time intervals (third column of the TIMER output) as clock times. Time intervals are the intervals between clicks; these are not clock times.
0 15.5
1.06 13.9
2.31 12.3
3.56 10.5
4.84 8.8
6.28 7.1
8.14 5.3
10.46 3.4
13.41 1.6
18.66 0
#$&*
You data could be put into the following format:
clock time (in seconds, measured from first reading) Depth of water (in centimeters, measured from the hole)
0
14
10
10
20
7
etc.
etc.
Your numbers will of course differ from those on the table.
The following questions were posed above. Do your data support or contradict the answers you gave above?
Is the depth changing at a regular rate, at a faster and faster rate, or at a slower and slower rate?
slower and slower
#$&*
Sketch a graph of depth vs. clock time (remember that the convention is y vs. x; the quantity in front of the 'vs.' goes on the vertical axis, the quantity after the 'vs.' on the horizontal axis). You may if you wish print out and use the grid below.
Describe your graph in the language of the Describing Graphs exercise.
negative exponential slope
#$&*
caution: Be sure you didn't make the common mistake of putting time intervals into the first column; you should put in clock times. If you made that error you still have time to correct it. If you aren't sure you are welcome to submit your work to this point in order to verify that you really have clock times and not time intervals
Now analyze the motion of the water surface:
For each time interval, find the average velocity of the water surface.
Explain how you obtained your average velocities, and list them:
Average velocity is change in distance over change in time
1.509433962 cm/s
0.474777448
0.306643952
0.202380952
0.152877698
0.12482663
0.102150538
0.075408463
0.049890864
It looks like you divided the change in position by the clock time, rather than by the change in the clock time.
For example the last interval shows a change in position of -1.6 cm, while the clock time changes by roughly 5 seconds. This would imply an average velocity of -1.6 cm / (5 seconds) = -.3 cm/s, not .0499 cm/s.
#$&*
Assume that this average velocity occurs at the midpoint of the corresponding time interval.
What are the clock times at the midpoints of your time intervals, and how did you obtain them? (Give one midpoint for each time interval; note that it is midpoint clock time that is being requested, not just half of the time interval. The midpoint clock time is what the clock would read halfway through the interval. Again be sure you haven't confused clock times with time intervals. Do not make the common mistake of reporting half of the time interval, i.e., half the number in the third column of the TIMER's output):
Change in distance / velocity = time
Midpoint distance is calulated by (d1-d2)/2
The midpoint between two positions would be found by averaging the two positions, which involves adding them and dividing by 2.
0.53
1.685
2.935
4.2
5.56
7.21
9.3
11.935
16.035
#$&*
Make a table of average velocity vs. clock time. The clock time on your table should be the midpoint clock time calculated above.
Give your table below, giving one average velocity and one clock time in each line. You will have a line for each time interval, with clock time first, followed by a comma, then the average velocity.
0.53,1.51
1.685,0.47
2.935,0.31
4.2,0.20
5.56,0.15
7.21,0.12
9.3,0.10
11.935,0.075
16.035,0.050
If you correct your calculations of the average velocities, your table will be correct. Midpoint clock times look OK.
#$&*
Sketch a graph of average velocity vs. clock time. Describe your graph, using the language of the Describing Graphs exercise.
negative exponential slope
Actually quadratic rather than exponential, but we won't worry too much about that distinction in this course.
#$&*
For each time interval of your average velocity vs. clock time table determine the average acceleration of the water surface. Explain how you obtained your acceleration values.
#$&*
Make a table of average acceleration vs. clock time, using the clock time at the midpoint of each time interval with the corresponding acceleration.
Give your table in the box below, giving on each line a midpoint clock time followed by a comma followed by acceleration.
#$&*
Answer two questions below:
Do your data indicate that the acceleration of the water surface is constant, increasing or decreasing, or are your results inconclusive on this question?
Do you think the acceleration of the water surface is actually constant, increasing or decreasing?
Data is inconclusive on this question.
I believe that the acceleration of the waters surface is decreasing.
#$&*
Your instructor is trying to gauge the typical time spent by students on these experiments. Please answer the following question as accurately as you can, understanding that your answer will be used only for the stated purpose and has no bearing on your grades:
Approximately how long did it take you to complete this experiment?
~ 2 hours
#$&*
Your work is pretty good and you seem to have the background for this course. You did make a basic error in calculating velocities (right idea, but incorrect denominator, easy to fix).
&#Please see my notes and submit a copy of this document with revisions and/or questions, and mark your insertions with &&&& (please mark each insertion at the beginning and at the end). &#