#$&*
phy 122
Your 'bottle thermometer' report has been received. Scroll down through the document to see any comments I might have inserted, and my final comment at the end.
** Bottle Thermometer_labelMessages **
I stopped short of finishing this lab because I believe my system is too inadequate for me to successfully complete the assignment. If you are not opposed to spending some time with me one day showing me how the system is supposed to be set up, I would be confident in my abilities to replicate the setup in my home and finish the lab. As far as my inexperience with some of the equations goes, I am in the transitional period where they are molding well but it will take some hammering down for them to properly set, which i plan to do this weekend. I might as well also tell you I'll be taking the first test on saturday if you wish to be on the look out for it. Your office hours online say they are for the spring schedule but if they are correct, I will stop by your office on tuesday and we can work this matter out in person. Thanks so much for all you do.
** **
** **
Copy this document, from this point to the end, into a word processor or text editor.
Follow the instructions, fill in your data and the results of your analysis in the given format.
Regularly save your document to your computer as you work.
When you have completed your work:
Copy the document into a text editor (e.g., Notepad; but NOT into a word processor or html editor, e.g., NOT into Word or FrontPage).
Highlight the contents of the text editor, and copy and paste those contents into the indicated box at the end of this form.
Click the Submit button and save your form confirmation.
Data program is at http://www.vhcc.edu/dsmith/genInfo/labrynth_created_fall_05/levl1_15\levl2_51/dataProgram.
exe
________________________________________
You can use the bottle, stopper and tubes as a very sensitive thermometer. This thermometer will have excellent precision, clearly registering temperature changes on the order of .01 degree. The system will also demonstrate a very basic thermal engine and its thermodynamic properties.
Set up your system with a vertical tube and a pressure-indicating tube, as in the experiment on measuring atmospheric pressure. There should be half a liter or so of water in the bottom of the container.
Refer back to the experiment 'Measuring Atmospheric Pressure' for a detailed description of how the pressure-indicating tube is constructed for the 'stopper' version of the experiment.
For the bottle-cap version, the pressure-indicating tube is the second-longest tube. The end inside the bottle should be open to the gas inside the bottle (a few cm of tube inside the bottle is sufficient) and the other end should be capped.
The figure below shows the basic shape of the tube; the left end extends down into the bottle and the capped end will be somewhere off to the right. The essential property of the tube is that when the pressure in the bottle increases, more force is exerted on the left-hand side of the 'plug' of liquid, which moves to the right until the compression of air in the 'plugged' end balances it. As long as the liquid 'plug' cannot 'leak' its liquid to the left or to the right, and as long as the air column in the plugged end is of significant length so it can be measured accurately, the tube is set up correctly.
If you pressurize the gas inside the tube, water will rise accordingly in the vertical tube. If the temperature changes but the system is not otherwise tampered with, the pressure and hence the level of water in the tube will change accordingly.
When the tube is sealed, pressure is atmospheric and the system is unable to sustain a water column in the vertical tube. So the pressure must be increased. Various means exist for increasing the pressure in the system.
You could squeeze the bottle and maintain enough pressure to support, for example, a 50 cm column. However the strength of your squeeze would vary over time and the height of the water column would end up varying in response to many factors not directly related to small temperature changes.
You could compress the bottle using mechanical means, such as a clamp. This could work well for a flexible bottle such as the one you are using, but would not generalize to a typical rigid container.
You could use a source of compressed air to pressurize the bottle. For the purposes of this experiment, a low pressure, on the order of a few thousand Pascals (a few hudredths of an atmosphere) would suffice.
The means we will choose is the low-pressure source, which is readily available to every living land animal. We all need to regularly, several times a minute, increase and decrease the pressure in our lungs in order to breathe. We're going to take advantage of this capacity and simply blow a little air into the bottle.
Caution: The pressure you will need to exert and the amount of air you will need to blow into the system will both be less than that required to blow up a typical toy balloon. However, if you have a physical condition that makes it inadvisable for you to do this, let the instructor know. There is an alternative way to pressurize the system.
You recall that it takes a pretty good squeeze to raise air 50 cm in the bottle. You will be surprised at how much easier it is to use your diaphragm to accomplish the same thing. If you open the 'pressure valve', which in this case consists of removing the terminating cap from the third tube, you can then use the vertical tube as a 'drinking straw' to draw water up into it. Most people can easily manage a 50 cm; however don't take this as a challenge. This isn't a test of how far you can raise the water.
Instructions follow:
Before you put your mouth on the tube, make sure it's clean and make sure there's nothing in the bottle you wouldn't want to drink. The bottle and the end of the tube can be cleaned, and you can run a cleaner through the tube (rubbing alcohol works well to sterilize the tube). If you're careful you aren't likely to ingest anything, but of course you want the end of the tube to be clean.
Once the system is clean, just do this. Pull water up into the tube. While maintaining the water at a certain height, replace the cap on the pressure-valve tube and think for a minute about what's going to happen when you remove the tube from your mouth. Also think about what, if anything, is going to happen to the length of the air column at the end of the pressure-indicating tube. Then go ahead and remove the tube from your mouth and watch what happens.
Describe below what happens and what you expected to happen. Also indicate why you think this happens.
I covered the pressure release valve with my finger and put the long end of the vertical tube into my mouth and began to suck like a drinking straw. It took very little effort to bring the water up into the tube. Upon removing my finger from the pressure valve, or taking my mouth off the tube, some of the water flowed back into the bottle, the rest I blew back in with my mouth.
#$&*
Now think about what will happen if you remove the cap from the pressure-valve tube. Will air escape from the system? Why would you or would you not expect it to do so?
Go ahead and remove the cap, and report your expectations and your observations below.
If I were to remove the cap and not hold the tube at such an angle as to prevent the water from escaping it would do so, air can escape the system when there is no water in the tube to prevent it from doing so.
#$&*
Now replace the cap on the pressure-valve tube and, while keeping an eye on the air column in the pressure-indicating tube, blow just a little air through the vertical tube, making some bubbles in the water inside the tube. Blow enough that the air column in the pressure-indicating tube moves a little, but not more than half a centimeter or so. Then remove the tube from your mouth, keeping an eye on the pressure-indicating tube and also on the vertical tube.
What happens?
When I blew on the tube with the pressure valve open, bubbles were made and it was clear air was being pushed into the bottle, but it was coming out the valve and not moving our pressure meter at all, if I held the pressure valve closed, the meter moved but only about a cm or so, any more would have been extremely difficult.
#$&*
Why did the length of the air column in the pressure-indicating tube change length when you blew air into the system? Did the air column move back to its original position when you removed the tube from your mouth? Did it move at all when you did so?
The air column moved slightly when the pressure valve was closed, upon releasing the valve or removing the tube from my mouth, the air column returned to its original position
#$&*
What happened in the vertical tube?
Any bubbles of water or bits of air in the column were forced back into the bottle, clearing out the tube.
****
#$&*
Why did all these things happen? Which would would you have anticipated, and which would you not have anticipated?
It was easy to see that blowing on the tube would increase the amount of air molecules and the overall pressure of the system. Its more difficult for me to describe the processes at work when one sucks water into the bottle, but here a form of pressure is also added. Perhaps since the tube is submerged, there is a decrease in volume of the water, but there may not be any forces acting on the bottle, just on the tube and the water.
#$&*
What happened to the quantities P, V, n and T during various phases of this process?
The number of moles of air could have likely increased upon blowing more air into the bottle, pressure would have also increased, temperature should have increased since a change in temp represents a change in pressure and vice versa. Volume would have decreased upon pulling more water into the tube, but more it less it stays constant. Less volume would have given more room for the air molecules to bounce around , there would be less collisions and less pressure. If air is blown into the system increasing the amount of air molecules and thus the number of collisions, this increase in collisions will increase the kinetic energy of the molecules in the bottle and will cause a temperature increase.
#$&*
Place the thermometer that came with your kit near the bottle, with the bulb not touching any surface so that it is sure to measure the air temperature in the vicinity of the bottle and leave it alone until you need to read it.
Now you will blow enough air into the bottle to raise water in the vertical tube to a position a little ways above the top of the bottle.
????If the pressure valve is open, water will not enter into the vertical tube, Im assuming were not supposed to be blowing into the vertical tube if were trying to get water to go up the vertical tube. The other length of tube is my air column for air pressure, how do we make this possible????
Use the pressure-valve tube to equalize the pressure once more with atmospheric (i.e., take the cap off). Measure the length of the air column in the pressure-indicating tube, and as you did before place a measuring device in the vicinity of the meniscus in this tube.Replace the cap on the pressure-valve tube and again blow a little bit of air into the bottle through the vertical tube. Remove the tube from your mouth and see how far the water column rises. Blow in a little more air and remove the tube from your mouth. Repeat until water has reached a level about 10 cm above the top of the bottle.
????Again the pressure valve is capped and the other tube is capped to contain the air column for measuring pressure, by what means are we to blow air into the system to raise water in the vertical tube. The only tube available for blowing is the vertical tube????
Place the bottle in a pan, a bowl or a basin to catch the water you will soon pour over it.
Secure the vertical tube in a vertical or nearly-vertical position.
The water column is now supported by excess pressure in the bottle. This excess pressure is between a few hundredths and a tenth of an atmosphere.
The pressure in the bottle is probably in the range from 103 kPa to 110 kPa, depending on your altitude above sea level and on how high you chose to make the water column. You are going to make a few estimates, using 100 kPa as the approximate round-number pressure in the bottle, and 300 K as the approximate round-number air temperature. Using these ball-park figures:
If gas pressure in the bottle changed by 1%, by how many N/m^2 would it change?
A 1 percent increase in pressure would increase the atmostpheric pressure of 100kPa by 1 to 101kPa.
#$&*
What would be the corresponding change in the height of the supported air column?
Not by much perhaps a few centimeters.
#$&*
By what percent would air temperature have to change to result in this change in pressure, assuming that the container volume remains constant?
****
I should be able to determine this by using the properties of PV = nRT however I am not comfortable enough with these properties yet to make an accurate prediction. The air temperature would change by the same amount since the quantities are proportional.
#$&*
Continuing the above assumptions:
How many degrees of temperature change would correspond to a 1% change in temperature?
****
#$&*
How much pressure change would correspond to a 1 degree change in temperature?
****
#$&*
By how much would the vertical position of the water column change with a 1 degree change in temperature?
****
#$&*
How much temperature change would correspond to a 1 cm difference in the height of the column?
****
#$&*
How much temperature change would correspond to a 1 mm difference in the height of the column?
I cannot at this stage in the course and with my current understanding answer these questions.
#$&*
A change in temperature of 1 Kelvin or Celsius degree in the gas inside the container should correspond to a little more than a 3 cm change in the height of the water column. A change of 1 Fahrenheit degree should correspond to a little less than a 2 cm change in the height of the water column. Your results should be consistent with these figures; if not, keep the correct figures in mind as you make your observations.
The temperature in your room is not likely to be completely steady. You will first see whether this system reveals any temperature fluctuations:
Make a mark, or fasten a small piece of clear tape, at the position of the water column.
Observe, at 30-second intervals, the temperature on your alcohol thermometer and the height of the water column relative to the mark or tape (above the tape is positive, below the tape is negative).
Try to estimate the temperatures on the alcohol thermometer to the nearest .1 degree, though you won't be completely accurate at this level of precision.
Make these observations for 10 minutes.
Report in units of Celsius vs. cm your 20 water column position vs. temperature observations, in the form of a comma-delimited table below.
****
The temperature and the air column do not fluctuate noticeable at all
What am I doing wrong?
#$&*
Describe the trend of temperature fluctuations. Also include an estimate (or if you prefer two estimates) based on both the alcohol thermometer and the 'bottle thermometer' the maximum deviation in temperature over the 10-minute period. Explain the basis for your estimate(s):
Again there were simply no noticeable fluctuations in the thermometer or the air column
#$&*
Now you will change the temperature of the gas in the system by a few degrees and observe the response of the vertical water column:
Read the alcohol thermometer once more and note the reading.
Pour a single cup of warm tap water over the sides of the bottle and note the water-column altitude relative to your tape, noting altitudes at 15-second intervals.
Continue until you are reasonably sure that the temperature of the system has returned to room temperature and any fluctuations in the column height are again just the result of fluctuations in room temperature. However don't take data on this part for more than 10 minutes.
Report your results below:
I was not able to get water to go up into the vertical column and stay there without having to cap the portion inside the bottle, which would have separated the column from the changing pressure of the system. The air column in the shorter tube that Ive been referring to as a primitive pressure gauge did move by about 2 cm.
#$&*
If your hands are cold, warm them for a minute in warm water. Then hold the palms of your hands very close to the walls of the container, being careful not to touch the walls. Keep your hands there for about a minute, and keep an eye on the air column.
Did your hands warm the air in the bottle measurably? If so, by how much? Give the basis for your answer:
This portion of the lab has me feeling less like a hapless physics pupil and more like a jedi.. making progress here but there did not seem to be a seriously noticeable change in the air column, perhaps my system is not sensitive enough or my lack of sustaining a successful vertical air column has botched my results.
#$&*
Now reorient the vertical tube so that after rising out of the bottle the tube becomes horizontal. It's OK if some of the water in the tube leaks out during this process. What you want to achieve is an open horizontal tube,, about 30 cm above the level of water in the container, with the last few centimeters of the liquid in the horizontal portion of the tube and at least a foot of air between the meniscus and the end of the tube.
The system might look something like the picture below, but the tube running across the table would be more perfectly horizontal.
Place a piece of tape at the position of the vertical-tube meniscus (actually now the horizontal-tube meniscus). As you did earlier, observe the alcohol thermometer and the position of the meniscus at 30-second intervals, but this time for only 5 minutes. Report your results below in the same table format and using the same units you used previously:
I must be doing something wrong but its difficult to tell what, I cant see how else the tube is supposed to be set up to where water will go into the tube and not fall back into the bottle, I previously explained why I eliminated the possibility of blowing into the system, pulling water like a straw doesnt work either. Regardless, I can see that on a very minute scale, perhaps not as minute as what Im thinking, that temperature fluctuates, that is certainly a fair statement. Given the nature of the system and its many possibilities for error though I dont understand how were going to see those changes, especially since I stared at a thermometer for a solid 5 minutes and there were no changes what so ever.
#$&*
Repeat the experiment with your warm hands near the bottle. Report below what you observe:
****
#$&*
When in the first bottle experiment you squeezed water into a horizontal section of the tube, how much additional pressure was required to move water along the horizontal section?
By how much do you think the pressure in the bottle changed as the water moved along the horizontal tube?
****
#$&*
If the water moved 10 cm along the horizontal tube, whose inner diameter is about 3 millimeters, by how much would the volume of air inside the system change?
****
#$&*
By what percent would the volume of the air inside the container therefore change?
****
#$&*
Assuming constant pressure, how much change in temperature would be required to achieve this change in volume?
****
#$&*
If the air temperature inside the bottle was 600 K rather than about 300 K, how would your answer to the preceding question change?
****
#$&*
There were also changes in volume when the water was rising and falling in the vertical tube. Why didn't we worry about the volume change of the air in that case? Would that have made a significant difference in our estimates of temperature change?
****
#$&*
If the tube was not completely horizontal, would that affect our estimate of the temperature difference?
For example consider the tube in the picture below.
Suppose that in the process of moving 10 cm along the tube, the meniscus moves 6 cm in the vertical direction.
By how much would the pressure of the gas have to change to increase the altitude of the water by 6 cm?
****
#$&*
Assuming a temperature in the neighborhood of 300 K, how much temperature change would be required, at constant volume, to achieve this pressure increase?
****
#$&*
The volume of the gas would change by the additional volume occupied by the water in the tube, in this case about .7 cm^3. Assuming that there are 3 liters of gas in the container, how much temperature change would be necessary to increase the gas volume by .7 cm^3?
****
#$&*
Continue to assume a temperature near 300 K and a volume near 3 liters:
If the tube was in the completely vertical position, by how much would the position of the meniscus change as a result of a 1 degree temperature increase?
****
#$&*
What would be the change if the tube at the position of the meniscus was perfectly horizontal? You may use the fact that the inside volume of a 10 cm length tube is .7 cm^3.
****
#$&*
A what slope do you think the change in the position of the meniscus would be half as much as your last result?
****
#$&*
@&
I'll look forward to meeting you on Tuesday. I believe you can make some significant contributions to this lab. We'll also try to figure out how to make the instructions clearer.
I do know I have at least one meeting with an advisee on Tuesday. I don't have my schedule handy, and the meeting usually do not last long so we should be able to work around it, but if you email me and let me know roughly when you plan to come by I'll try to avoid scheduling other meetings that might conflict.
*@