#$&*
PHY 201
Your 'initial timing experiment' report has been received. Scroll down through the document to see any comments I might have inserted, and my final comment at the end.
** Initial Timing Experiment_labelMessages **
** **
Copy this document, from this point to the end, into a word processor or text editor.
• Follow the instructions, fill in your data and the results of your analysis in the given format.
• Regularly save your document to your computer as you work.
• When you have completed your work: Copy the document into a text editor (e.g., Notepad; but NOT into a word processor or html editor, e.g., NOT into Word or FrontPage). Highlight the contents of the text editor, and copy and paste those contents into the indicated box at the end of this form. Click the Submit button and save your form confirmation.
Note: The majority of student report taking less than an hour on this experiment, though a few report significantly longer times.
Take reasonable care to get good data in this experiment. Try to do the timing as accurately as possible. Measurements of length, height, etc. should be reasonably accurate (e.g., with a meter stick or ruler you can measure to withing +- 1 millimeter, but it's not necessary to try to determine fractions of a millimeter).
In this experiment you will use the TIMER program, a hardcover book, the toy car that came in your lab materials package (or, if you do not yet have the package, a cylinder or some other object that will roll along the book in a relatively straight line), and a ruler or the equivalent (if you don't have one, note the Rulers link, which is also given on the Assignments page).
• The book's cover should be straight and unbent.
• The toy car (or other object) should roll fairly smoothly.
Place the book on a flat level tabletop. You will prop one end of the book up a little bit, so that when it is released the object will roll without your assistance, gradually speeding up, from the propped-up end to the lower end. However don't prop the end up too much. It should take at least two seconds for the ball to roll down the length of the book when it is released from rest. For a typical book, a stack of two or three quarters placed under one end works well.
• Using the TIMER program determine how long it takes the ball to roll from one end of the ramp to the other, when released from rest. Once you've got the book set up, it takes only a few seconds to do a timing, so it won't take you long to time the object's motion at least three times.
• Determine how far the object travels as it rolls from its initial position (where you first click the timer) to its final position (where you click at the end of the interval). This will probably be a bit less than the length of the book, due to the length of the object itself.
• Determine how much higher one end of the book was than the other, and how far it is from the supports (e.g., the stack of quarters, or whatever you used to support one end) to the end of the book which rests on the table.
Then reverse the direction of the book on the tabletop, rotating the book an its supports (e.g., the stack of quarters) 180 degrees so that the ball will roll in exactly the opposite direction. Repeat your measurements.
In the box below describe your setup, being as specific as possible about the book used (title, ISBN) and the object being used (e.g., a can of vegetables (full or empty; should be specified) or a jar (again full or empty); anything round and smooth that will upon release roll fairly slowly down the incline), and what you used to prop the object up (be as specific as possible). Also describe how well the object rolled--did it roll smoothly, did it speed up and slow down, did it roll in a straight line or did its direction change somewhat?
your brief discussion/description/explanation:
I used my Physics book(Giancoli, 6th edition, volume 1) and I propped it up with a Texas Instruments graphing calculator User’s Manual ¼ inch thick. I used a lead ball out of an old Gateway mouse. The surface of the incline was 11 inches in length. I rolled it down the book ten times, five one way and five after a 180 degree turn, and my average time was 2.2.0870625 seconds.
#$&* (note that your answer should always start in one of the blank lines preceding the #$&* mark)
In the space indicated below report your data. State exactly what was measured, how it was measured, how accurately you believe it was measured and of course what the measurements were. Try to organize your report so the reader can easily scan your data and identify any patterns or trends.
your brief discussion/description/explanation:
Roll 1-5
1. 2.46875
2. 2.046875
3. 2.15625
4. 2.125
5. 2.125
average:2.184375
Roll 6-10 (180 degree turn of ramp)
6. 1.96875
7. 2.109375
8. 1.84375
9. 2.171875
10. 2.125
Average: 2.04375
Average 2.0870625
#$&*
Using your data determine how fast the object was moving, on the average, as it rolled down the incline. Estimate how accurately you believe you were able to determine the object's average speed, and give the best reasons you can for your estimate of the accuracy.
your brief discussion/description/explanation:
Average speed was 5.271 inches per second. 11 divided 2.0870625 equals 5.270565687
I think this is a fairly accurate speed, event though I was using an average time not an exact time. If more time and effort were put into the experiment, we would pobably be able to come up with more precise data.
#$&*
How fast was the object moving at the beginning of the timed interval?
According to your previous calculation, what was its average speed during this interval?
Do you think the object, when it reached the lower end of the book, was moving at a speed greater or less than the average speed you calculated?
your brief discussion/description/explanation:
At the beginning of the timed interval that object is moving at a speed less than the average speed.
average speed is 5.271 in/sec
As the object reached the lower end of the boos it was moving at a speed greater than the average speed calculated.
#$&*
List the following in order, from least to greatest. Indicate 'ties': The object's initial speed, its final speed, its average speed, and the change in its speed as it rolled from one end of the book to the other.
your brief discussion/description/explanation:
change in speed, initial speed, average speed, final speed
The change in speed will not be great at all. The average speed will be in the middle since it is the average and as stated above the final speed will be greater than the average speed and the initial speed will be less than the average speed.
#$&*
Devise and conduct an experiment to determine whether or not the object is speeding up as it rolls down the incline. If you have set the experiment up as indicated, it should seem pretty obvious that the object is in fact speeding up. But figure out a way to use actual measurements to support your belief.
Explain how you designed and conducted your experiment, give your data and explain how your data support your conclusions.
your brief discussion/description/explanation:
I made a mark in the middle of the book and timed it rolling down the first half. then I rolled the ball down the book starting the timer at the mark in the middle and then ending it at the end. it took the ball longer to roll down the first half of the incline than the second half. Which makes sense.
#$&*
Your instructor is trying to gauge the typical time spent by students on these experiments. Please answer the following question as accurately as you can, understanding that your answer will be used only for the stated purpose and has no bearing on your grades:
Approximately how long did it take you to complete this experiment?
25 minutes
#$&*
You may also include optional comments and/or questions.
#$&*
Please copy your document into the box below and submit.
&#Your work on this lab exercise is good. Let me know if you have questions. &#