#$&*
Phy 201
Your 'cq_1_00.1' report has been received. Scroll down through the document to see any comments I might have inserted, and my final comment at the end.
** CQ_1_00.1_labelMessages **
The problem:
You don't have to actually do so, but it should be clear that if you wished to do so, you could take several observations of positions and clock times. The main point here is to think about how you would use that information if you did go to the trouble of collecting it. However, most students do not answer these questions in terms of position and clock time information. Some students do not pause the video as instructed. To be sure you are thinking in terms of positions and clock times, please take a minute to do the following, which should not take you more than a couple of minutes:
• Pick one of the videos, and write down the position and clock time of one of the objects, as best you can determine them, in each of three different frames. The three frames should all depict the same 'roll' down the ramp, i.e. the same video clip, at three different clock times. They should not include information from two or more different video clips.
• For each of the three readings, simply write down the clock time as it appears on the computer screen, and the position of the object along the meter stick. You can choose either object (i.e., either the pendulum or the roll of tape), but use the same object for all three measurements. Do not go to a lot of trouble to estimate the position with great accuracy. Just make the best estimates you can in a couple of minutes.
Which object did you choose and what were the three positions and the three clock times?
answer/question/discussion: ->->->->->->->->->->->-> (start in the next line):
I chose the pendulum.
Time 59.4 59.7 60.015
Place 6 11 16
#$&*
In the following you don't have to actually do calculations with your actual data. Simply explain how you would use data of this nature if you had a series of several position vs. clock time observations:
• If you did use observations of positions and clock times from this video, how accurately do you think you could determine the positions, and how accurately do you think you would know the clock times? Give a reasonable numerical answer to this question (e.g., positions within 1 meter, within 2 centimeters, within 3 inches, etc; clock times within 3 seconds, or within .002 seconds, or within .4 seconds, etc.). You should include an explanations of the basis for your estimate: Why did you make the estimate you did?
answer/question/discussion: ->->->->->->->->->->->-> (start in the next line):
I would not be very accurate in determining the position , but I could accurately determine the clock times. The position would be close to 2 inches in the same vicinities; however, the time would be close to .4 seconds because the stick that released the tape and pendulum could be blocking the last 2 numbers. The reasons why I made the estimate for the position so vague is the numbers on the measuring tape is blurry making it hard to read.
#$&*
• How can you use observations of position and clock time to determine whether the tape rolling along an incline is speeding up or slowing down?
answer/question/discussion: ->->->->->->->->->->->-> (start in the next line):
you could take the measurements from both instruments at the exact time several times seeing if they are side by side or one in front of the other. From there you should be able to conclude if one is moving faster or slowing down.
#$&*
• How can you use observations of position and clock time to determine whether the swinging pendulum is speeding up or slowing down?
answer/question/discussion: ->->->->->->->->->->->-> (start in the next line):
you can take the distance it traveled from near the beginning and compare it to the distance it traveled towards the end.
#$&*
• Challenge (University Physics students should attempt answer Challenge questions; Principles of Physics and General College Physics may do so but it is optional for these students): It is obvious that a pendulum swinging back and forth speeds up at times, and slows down at times. How could you determine, by measuring positions and clock times, at what location a swinging pendulum starts slowing down?
answer/question/discussion: ->->->->->->->->->->->-> (start in the next line):
you could estimate the location at which it begins to slow down by charting the time that has past to the distance it has traveled. Then you draw a line through the points and you could see that the graph would decrease at some point. From there you should be able to estimate between this time and locate the pendulum began to slow down.
#$&*
• Challenge (University Physics students should attempt answer Challenge questions; Principles of Physics and General College Physics may do so but it is optional for these students): How could you use your observations to determine whether the rate at which the tape is speeding up is constant, increasing or decreasing?
answer/question/discussion: ->->->->->->->->->->->-> (start in the next line):
you could graph the data you have. From there you could see if the there is a consistent rise, declination, or a random rise in the distance it traveled in comparison to the time elapsed.
#$&*
*#&!
&#This looks good. Let me know if you have any questions. &#