#$&*
course PHY 232
Question: Suppose you measure the length of a pencil. You use both a triply-reduced ruler and the original ruler itself, and you make your measurements accurate to the smallest mark on each. You then multiply the reading on the triply-reduced ruler by the appropriate scale factor.
· Which result is likely to be closer to the actual length of the pencil?
your answer: vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv
The result that might be closer to the actual length of the ruler is Original ruler since the reading does not need to be manipulated.
#$&*
· What factors do you have to consider in order to answer this question and how do they weigh into your final answer?
your answer: vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv
We first consider the precision factor, having a triple reduced ruler and multiplying the result could affect how accurate the reasult would turn out to be but as for the
original ruler you can obtain the precise measurement and do
not need to be manipulated.
#$&*
*********************************************
Question: Answer the same questions as before, except assume that the triply-reduced ruler has no optical distortion, and that you also know the scale factor accurate to 4 significant figures.
· Which result is likely to be closer to the actual length of the pencil?
your answer: vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv
Since the triple-reduced ruler has no optical distortion and the scale is accurate then it would be most likely to be the
closest as compared to the original ruler.
#$&*
· What factors do you have to consider in order to answer this question and how do they weigh into your final answer?
your answer: vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv
Some factors to consider would be optical distortion and accuracy, and since the triple-reduced ruler does not have
any optical distortion and the scale is accurate to atleast 4 significant figues then we may consider its reasults.
#$&*
*********************************************
Question: Suppose you are to measure the length of a rubber band whose original length is around 10 cm, measuring once while the rubber band supports the weight of a small apple and again when it supports the weight of two small apples. You are asked to report as accurately as possible the difference in the two lengths, which is somewhere between 1 cm and 2 cm. You have available the singly-reduced copy and the triply-reduced copy, and your data from the optical distortion experiment.
· Which ruler will be likely to give you the more accurate difference in the lengths?
your answer: vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv
singly reduced ruler
#$&*
· Explain what factors you considered and how they influence your final answer.
your answer: vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv
I considered precision and the optical distortion part too,
for the singly-reduced it will report less significant figures, but for the triply-reduced ruler will report more signifact figures and since both might have no optical distortion that enables me to choose the ruler with the closet accurate measurement.
#$&*
*********************************************
Question: Later in the course you will observe how the depth of water in a uniform cylinder changes as a function of time, when water flows from a hole near the bottom of the cylinder. Suppose these measurements are made by taping a triply-reduced ruler to the side of a transparent cylinder, and observing the depth of the water at regular 3-second intervals.
The resulting data would consist of a table of water depth vs. clock times, with clock times 0, 3, 6, 9, 12, ... seconds. As depth decreases the water flows from the hole more and more slowly, so the depth changes less and less quickly with respect to clock time.
Experimental uncertainties would occur due to the optical distortion of the copied rulers, due to the spacing between marks on the rulers, due to limitations on your ability to read the ruler (your eyes are only so good), due to timing errors, and due to other possible factors.
Suppose that depth changes vary from 5 cm to 2 cm over the first six 3-second intervals.
Assume also that the timing was very precise, so that there were no significant uncertainties due to timing.
· Based on what you have learned in experiments done through Assignment 1, without doing extensive mathematical analysis, estimate how much uncertainty would be expected in the observed depths, and briefly explain the basis for your estimates. Speculate also on how much uncertainty would result in first-difference calculations done with the depth vs. clock time data, and how much in second-difference calculations.
your answer: vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv
Since within a 3 second preiod the depth decreases from 5cm to 2cm which the difference is 3cm showing for every 1cm depth was covered in a second which is fast but not precise.Also because of the optical distortion we can tend to misjudge the
reading. Although the reading on the first data collecting also shows a similar trend of 3seconds for every depth.
#$&*
· How would these uncertainties affect a graph of first difference vs. midpoint clock time, and how would they affect a graph of second difference vs. midpoint clock time?
your answer: vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv
Due to the inconsitancy and fluctuation of the flow and time that could potentially affect the rise or run on the graph.
#$&*
· How reliably do you think the first-difference graph would predict the actual behavior of the first difference?
your answer: vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv
Depending on the precision factor the first difference would be probably be slightly reliable in predicting the behaivour of the graph.
#$&*
· Answer the same for the second-difference graph.
your answer: vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv
As for the second difference graph it would be reliable in explaing the rise or run although there might be some fluctuations
here and there.
#$&*
· What do you think the first difference tells you about the system? What about the second difference?
your answer: vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv
That there is some sought of level of accuracy involved while for the second could be used to show the constant acceleration of the system.
#$&*
*********************************************
Question: Suppose the actual second-difference behavior of the depth vs. clock time is in fact linear. How nearly do you think you could estimate the slope of that graph from data taken as indicated above (e.g., within 1% of the correct slope, within 10%, within 30%, or would no slope be apparent in the second-difference graph)?
your answer: vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv
I think i would estimate it to more than 30% when describing the slope.
#$&*
Again no extensive analysis is expected, but give a brief synopsis of how you considered various effects in arriving at your estimate.
your answer: vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv
Picking two points any where on the graph and finding there slope using the slope equation and approximating how close it would for comparison purposes.
#$&*"
&#Good responses. Let me know if you have questions. &#