Phy 231
Your 'cq_1_00.1' report has been received. Scroll down through the document to see any comments I might have inserted, and my final comment at the end.
** **
The problem:
You don't have to actually do so, but it should be clear that if you wished to do so, you could take several observations of positions and clock times. The main point here is to think about how you would use that information if you did go to the trouble of collecting it. However, most students do not answer these questions in terms of position and clock time information. Some students do not pause the video as instructed. To be sure you are thinking in terms of positions and clock times, please take a minute to do the following, which should not take you more than a couple of minutes:
• Pick one of the videos, and write down the position and clock time of one of the objects, as best you can determine them, in each of three different frames. The three frames should all depict the same 'roll' down the ramp, i.e. the same video clip, at three different clock times. They should not include information from two or more different video clips.
• For each of the three readings, simply write down the clock time as it appears on the computer screen, and the position of the object along the meter stick. You can choose either object (i.e., either the pendulum or the roll of tape), but use the same object for all three measurements. Do not go to a lot of trouble to estimate the position with great accuracy. Just make the best estimates you can in a couple of minutes.
Which object did you choose and what were the three positions and the three clock times?
answer/question/discussion: ->->->->->->->->->->->-> (start in the next line):
Object 1 on the video it started at 59.00 roughly, middle 59.65 roughly quit at roughly 60.00
1 15.498 15.498
2 16.17 0.672
3 16.6 0.43
#$&*
In the following you don't have to actually do calculations with your actual data. Simply explain how you would use data of this nature if you had a series of several position vs. clock time observations:
• If you did use observations of positions and clock times from this video, how accurately do you think you could determine the positions, and how accurately do you think you would know the clock times? Give a reasonable numerical answer to this question (e.g., positions within 1 meter, within 2 centimeters, within 3 inches, etc; clock times within 3 seconds, or within .002 seconds, or within .4 seconds, etc.). You should include an explanations of the basis for your estimate: Why did you make the estimate you did?
answer/question/discussion: ->->->->->->->->->->->-> (start in the next line):
The timer you can get the position of time accurate to the .001 seconds. Now as for the position of the tape it would much harder to judge exact location only an estimate by a .5in margin approx.
#$&*
• How can you use observations of position and clock time to determine whether the tape rolling along an incline is speeding up or slowing down?
answer/question/discussion: ->->->->->->->->->->->-> (start in the next line):
You could take 3 points and measure the time difference between 1 and 2 and then 2 and 3 as long as the distance is the same. If the time changes then a speed change has occurred.
#$&*
• How can you use observations of position and clock time to determine whether the swinging pendulum is speeding up or slowing down?
answer/question/discussion: ->->->->->->->->->->->-> (start in the next line):
Again you could take 3 points and measure the time difference between 1 and 2 and then 2 and 3 as long as the distance is the same. If the time changes then a speed change has occurred.
#$&*
• Challenge (University Physics students should attempt answer Challenge questions; Principles of Physics and General College Physics may do so but it is optional for these students): It is obvious that a pendulum swinging back and forth speeds up at times, and slows down at times. How could you determine, by measuring positions and clock times, at what location a swinging pendulum starts slowing down?
answer/question/discussion: ->->->->->->->->->->->-> (start in the next line):
You could tell by the multiple plotted points and equal distance traveled by the change in time required to make set distances. Of course it is easily seen on the videos.
#$&*
• Challenge (University Physics students should attempt answer Challenge questions; Principles of Physics and General College Physics may do so but it is optional for these students): How could you use your observations to determine whether the rate at which the tape is speeding up is constant, increasing or decreasing?
answer/question/discussion: ->->->->->->->->->->->-> (start in the next line):
you can see between 0 ft plot and 1 ft plot the tape is roughly .65sec/ft from then from 1 to 2 it is moving at .35 sec/ft
#$&*
** **
30 mins
** **
6/7 11am
&#This looks good. Let me know if you have any questions. &#
&#Your work is mostly correct, and I believe you will understand everything after reading the document in the link below. You will be directed to submit a revision; however unless you have questions or comments, the revision is not necessary. Just be sure you understand all the important details in the document. &#