#$&*
Phy 201
Your 'timer program' report has been received. Scroll down through the document to see any comments I might have inserted, and my final comment at the end.
#$&* Your General Comment **
I was able to get the timer file and program to finally work today, but now I don't understand what the numbers in the first and second columns of my data represent. ???Is there anyway you could explain to me what they indicate???
#$&* Describe what you see on your first 10 clicks **
15 minutes
#$&*Your TIMER data from 20 fast clicks **
Operating the TIMER program
It is easy to operate the Timer program. All you have to do is click on the button labeled Click to Time Event.
Click that button about 10 times and describe what you see.
I see three columns, one with the numbers 1-10, one with 10 numbers that range from 21 to 25 and the last one that starts with the number 21.375 and then lists 9 numbers that are small decimals.
#$&*
Now click on Initialize Counter, which will clear all the data from the timer window. Click the mouse as fast as you can until the TIMER window fills up. Be sure you get at least 20 time intervals.
If you miss a click, try again. Keep trying until you get at least 20 intervals without a missed or delayed click.
Copy your data starting in the next line:
1 218.9844 218.9844
2 219.1875 .203125
3 219.3281 .140625
4 219.4219 .09375
5 219.5156 .09375
6 219.6406 .125
7 219.75 .109375
8 219.875 .125
9 220 .125
10 220.1094 .109375
11 220.2188 .109375
12 220.3438 .125
13 220.4688 .125
14 220.5938 .125
15 220.7188 .125
16 220.8594 .140625
17 220.9844 .125
18 221.1094 .125
19 221.25 .140625
20 221.3906 .140625
21 221.5 .109375
22 221.6563 .15625
#$&*
You got at least 20 time intervals. Based on your data what was the average of the first 20 time intervals? Note that you could get this average by averaging the first 20 intervals. My first few intervals were .15625, .15625, .1875, .171875, etc; I could just add up the first 20 intervals and divide by 20 to get the average. However there is an easier and quicker way to get the result, so use the easier way if you can.
Give your result, number only, in the first line, and starting in the second line explain how you got it.
0.19609375
I added up all the first 20 numbers in the third column and then I divided by 20 to get the average.
#$&*
@& Only one of your intervals was greater than this result, and that only by a small amount.
You didn't include the first interval, and that was appropriate since 218.98 seconds is clearly not a quickl-click interva.
So it's difficult to see how you obtained a mean of .196 seconds. I expect it was a simple arithmetic error.
In any result you would ideally recognize that this can't be correct.
Did you think of subtracting the two clock times and dividing by 20?*@
When I did this activity the first few lines of my data were as follows:
event number clock time time interval
1 11.67188 11.67188
2 11.875 0.203125
3 12.0625 0.1875
4 12.20313 0.140625
5 12.375 0.171875
6 12.54688 0.171875
7 12.73438 0.1875
8 12.92188 0.1875
9 13.10938 0.1875
10 13.28125 0.171875
11 13.4375 0.15625
It looks like the same intervals keep popping up. For example .1875 seconds occurs 5 times out of the first 10 intervals, .171875 seconds occurs three times, and .203125 seconds, .140625 seconds and .15625 seconds each occur once.
A frequency distribution for my time intervals would be as follows:
time interval frequency
,140625 1
.15625 1
.171875 3
.1875 5
.203125 1
What different time intervals did you observe in your first 20 intervals, and how many times did each occur? List below the different time intervals you observed and the number of times each occurred. List from the shortest to the longest interval, and use a comma between the time interval and its frequency. For example my data above would be listed at
.140625, 1
.1565, 1
.171875, 3
.1875, 5
.203125, 1
Your list should be in exactly this format, with no other symbols or characters.
0.09375, 2
0.109375, 4
0.125, 9
0.140625, 4
0.203125, 1
#$&*
You may make any comments or ask any question about the process so far in the box below
#$&*
On the 10 intervals I've shown you, do you really think I managed to get a time of .1875 seconds, accurate to 4 significant figures, on half of the intervals? If you do, I'm grateful for your confidence but I'm just not that good. No human being has that much neurological and muscular control.
So why do you think the TIMER program reported that time so frequently? Why weren't there times like .1830 seconds, or .1769 seconds? Does this mean that the TIMER program is flawed? Does that mean it's useless?
It probably reported that time so frequently as an average of the milliseconds you varied around that time so that you can have a better idea of your average time instead of many varying times. This does not mean the TIMER program is flawed or useless, it simply is giving you a better representation of you average time.
#$&*
Here are a few more lines of data, with an added column showing the difference between each time interval and the next.
clock time time interval difference from one time interval to next
9 13.10938 0.1875 -0.01563
10 13.28125 0.171875 -0.01563
11 13.4375 0.15625 0.03125
12 13.625 0.1875 -0.01563
13 13.79688 0.171875 0.015625
14 13.98438 0.1875 0.015625
15 14.1875 0.203125 -0.03125
16 14.35938 0.171875 -0.01563
17 14.51563 0.15625 0.03125
Take a good look at that last column and tell us what you see in those numbers, and what this tells you about the TIMER program
The last column is giving you an idea of what the next number is going to be based on the pattern it has noticed from the first 8 numbers.
#$&*
Now initialize the TIMER once more, and take a series of 10 relaxed breaths. Every time you start to inhale, hit the TIMER button.
My results for the first 7 complete breaths are as follows:
series of relaxed breaths
event number clock time time interval difference between time interval and next
1 1569.734 1569.734
2 1582.75 13.01563 0.32812
3 1596.094 13.34375 3.90625
4 1613.344 17.25 2.70313
5 1633.297 19.95313 1.35937
6 1654.609 21.3125 4.23438
7 1680.156 25.54688 2.15625
8 1707.859 27.70313
I didn't go on because the time between my breaths kept increasing, and I was afraid if I relaxed any more I might stop breathing altogether. It's going to take either more statistical analysis to determine whether that's a real danger, or a little common sense.
Report your results by just entering your time intervals, one to each line, in the box below. If I was entering my results I would enter
13.01563
13.34375
17.25
19.95313
21.3125
etc.
Enter your results in the same format:
3.84375
4.59375
4.375
4.5
4.21875
3.546875
4.453125
#$&*
If you have any comments please insert them here
#$&*
Most likely you did not observe the same exact time interval twice, and if you did it did not happen nearly as often as when you did the fact clicks.
Why do you think this is exactly what we would expect?
When you are performing a slower task, like breathing, the intervals in between are harder to estimate and coordinate because you have more time to perform your next breath whereas fast tasks such as the rapid clicking, are easier to perform in a fast uniform manner which is why those intervals had more in common.
#$&*
Which of the following statements do you think is the most accurate?
a. The TIMER program is capable of determining the time between two events accurately to within about .1 second.
b. The TIMER program is capable of determining the time between two events accurately to within about .01 second.
c. The TIMER program is capable of determining the time between two events accurately to within about .001 second.
d. The TIMER program is capable of determining the time between two events accurately to within about .0001 second.
Enter your answer and your reasoning below:
d. The TIMER program is capable of determining the time between two events accurately to within about .0001 second.
This is because many of the intervals are listed to the 6th decimal point which indicates its level of accuracy.
#$&*
Note that the TIMER.exe program can save your data in a format that can be read by a spreadsheet (the TIMER applet cannot do so). This will be very handy in the future, so take a minute and do the following:
1. Click on the button at the lower right of the TIMER form, entitled Click to File Data.
2. A box will pop up allowing you to include an identifying message. You should generally choose to include such a message; for the data presently on your timer that might be 'series of regular breaths time at beginning of inhalation' or something similar. Type in whatever you think would serve as a good identifier for this data and OK that box.
3. A typical Save As window will appear. Decide where to save your data and what to call it, and proceed to save it. The program will save the file as a comma-delimited text file.
4. Open your spreadsheet program (typically Excel) and choose File > Open. Browse to the folder in which you just saved your data. Below the File Name line will be a File Type line; set this either to Text Files or All Files so your file will appear. Open it.
5. A series of windows will typically appear. In the first window make sure the file type chosen is Delimited, the proceed to the next window.
6. In the second window you will see a series of checkboxes; check the one entitled Comma, in order to select the comma-delimited file, then just click on Finish.
If you can't run the .exe program, you can't do Steps 1-3. However all you need to do is copy the contents of the program to a text file, using copy-and-paste. Save that text file, using any filename you wish. Then proceed with steps 4-6 above.
Your data should appear in your spreadsheet, and can be manipulated as in any spreadsheet.
Copy a few lines of the data from your spreadsheet below:
series of regular breathing times
event number clock time time interval
1 1118.453 1118.453
2 1122.297 3.84375
3 1126.891 4.59375
4 1131.266 4.375
5 1135.766 4.5
6 1139.984 4.21875
7 1143.531 3.546875
8 1147.984 4.453125
#$&*
*#&!
&#This lab submittion looks good. See my notes. Let me know if you have any questions.
Revision isn't requested, but if you do choose to submit revisions, clarifications or questions, please insert them into a copy of this document, and mark your insertions with &&&& (please mark each insertion at the beginning and at the end).
Be sure to include the entire document, including my notes.
&#