course Phy 232
Question: This question, related to the use of the TIMER program in an experimental situation, is posed in terms of a familiar first-semester system.
Suppose you use a computer timer to time a steel ball 1 inch in diameter rolling down a straight wooden incline about 50 cm long. If the computer timer indicates that on five trials the times of an object down an incline are 2.42sec, 2.56 sec, 2.38 sec, 2.47 sec and 2.31 sec, then to what extent do you think the discrepancies could be explained by each of the following:
• The lack of precision of the TIMER program.
To what extent to you think the discrepancies are explained by this factor?
your answer: vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv
This factor does not have a major effect on the discrepancies because the values given are reported to two decimal places which is the extent of the accuracy of the TIMER program. If the values were given to any further decimal places then this factor would play a role in the discrepancies.
• The uncertain precision of human triggering (uncertainty associated with an actual human finger on a computer mouse)
To what extent to you think the discrepancies are explained by this factor?
your answer: vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv
This factor clearly plays a major role in the discrepancies because while most people have the hand eye coordination to hit the trigger at nearly the correct time, it is not humanly possible to record the correct time to the hundredth of a second and to an extent, the tenth of a second.
• Actual differences in the time required for the object to travel the same distance.
To what extent to you think the discrepancies are explained by this factor?
your answer: vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv
This factor shouldn’t have a major effect because while each run will never be exactly equal due to different factors, the runs should all be nearly equal as long they occur under essentially the same conditions.
• Differences in positioning the object prior to release.
To what extent to you think the discrepancies are explained by this factor?
your answer: vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv
This factor also should not have a major effect as long as the experimenter used some sort of mark or point of reference to start each run at the same place.
• Human uncertainty in observing exactly when the object reached the end of the incline.
To what extent to you think the discrepancies are explained by this factor?
your answer: vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv
Along with the human uncertainty in hitting the trigger, I believe this would be one of the biggest reasons for the discrepancy because once again, the human eye cannot observe this happening to the hundredth of a second.
*********************************************
Question: How much uncertainty do you think each of the following would actually contribute to the uncertainty in timing a number of trials for the ball-down-an-incline lab?
• The lack of precision of the TIMER program.
To what extent to you think this factor would contribute to the uncertainty?
your answer: vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv
As previously stated, the TIMER program is accurate to the hundredth of a second. Therefore, the uncertainty due to the TIMER program should be minimal and only occurs in the hundredths of the data.
• The uncertain precision of human triggering (uncertainty associated with an actual human finger on a computer mouse)
To what extent to you think this factor would contribute to the uncertainty?
your answer: vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv
This factor should be one of the biggest sources of uncertainty in comparison to the other factors.
• Actual differences in the time required for the object to travel the same distance.
To what extent to you think this factor would contribute to the uncertainty?
your answer: vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv
As long as the conditions of each trial are kept the same, this factor should not contribute greatly to the uncertainty.
• Differences in positioning the object prior to release.
To what extent to you think this factor would contribute to the uncertainty?
your answer: vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv
This factor should contribute to the uncertainty only slightly.
• Human uncertainty in observing exactly when the object reached the end of the incline.
To what extent to you think this factor would contribute to the uncertainty?
your answer: vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv
Along with imprecision of the human triggering, this factor should be an major source of uncertainty.
*********************************************
Question: What, if anything, could you do about the uncertainty due to each of the following? Address each specifically.
• The lack of precision of the TIMER program.
What do you think you could do about the uncertainty due to this factor?
your answer: vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv
This factor is not a major source of uncertainty. Nevertheless, aside from creating a new TIMER program, there is little that could be done about this.
• The uncertain precision of human triggering (uncertainty associated with an actual human finger on a computer mouse)
What do you think you could do about the uncertainty due to this factor?
your answer: vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv
One could set up a sensor or trigger that would automatically trigger the TIMER program at the correct time.
• Actual differences in the time required for the object to travel the same distance.
What do you think you could do about the uncertainty due to this factor?
your answer: vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv
Little could be done about this factor except for making sure the same object is used each time and stays in the same condition, and the track is free of defects and stays this way throughout the experiment.
• Differences in positioning the object prior to release.
What do you think you could do about the uncertainty due to this factor?
your answer: vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv
As stated before, some sort of mark or point of reference should be made on the track to ensure there is an objective way to position the object.
• Human uncertainty in observing exactly when the object reached the end of the incline.
What do you think you could do about the uncertainty due to this factor?
your answer: vvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvvv
A system of triggers or sensors could be set up that would objectively measure when the object reaches the end of the incline.
"
&#Very good work. Let me know if you have questions. &#
#$&*